Pet door fit · Passage and installation
Pet door size & installation checker
Check the opening your pet walks through, the thickness of your door and an existing installation hole separately. Compare six manufacturer-sourced sizes from two PetSafe Extreme Weather families.
Source review: October 5, 2026 · Inches or centimetres · Measurements are calculated in your browser.
Enter your actual measurements
Three different dimensions
Flap: usable passage for the pet. Cut-out: the hole made during installation. Frame: the outer part that mounts around the hole.
A passing passage check does not approve installation. No cutting dimensions should be taken from this illustration; use the exact product’s supplied template.
Measure the pet and the installation separately
- Pet width: measure the widest body area, usually the chest or hips. Use the individual pet rather than breed or weight alone.
- Body height: measure shoulder to the lowest chest or belly point. Floor-to-shoulder height is a different measurement used when placing the installation template.
- Planning allowance: choose additional total opening width and height. A 7-inch body width plus 1 inch requires an 8-inch opening, not a 1-inch gap on each side.
- Door thickness: measure the material where the unit will mount. Do not substitute a wall’s full depth or a decorative frame measurement.
- Existing cut-out: measure the actual installation hole in both dimensions. The old flap and old outer frame are not the hole size. Include its corner shape in the physical check.
- Flat panel space: measure the unobstructed area for the outer frame on both sides. The tool compares frame width and height only; fasteners, door edges and product-specific structural clearances remain separate.
In a multi-pet home, passage must accommodate each pet’s body dimensions. The widest animal and the one with the greatest body height may be different. Also check whether the installed step-over height suits the smaller pet; that cannot be established from a width-and-height rectangle.
Verified model dimensions: inches, width × height
These six records use the current product charts, checked against PetSafe’s published catalogue. Listed thickness is the product page’s standard solid-door range. Special adapters, wall tunnels, glass and screen installations are outside this dataset. The standard Plastic Pet Door family is omitted because its source tables disagree on some dimensions.
| Model / US catalogue part | Flap W × H | Cut-out W × H | Frame W × H | Door thickness | Source |
|---|---|---|---|---|---|
| PetSafe Extreme Weather Plastic — Small / PPA00-10984 | 5.125 × 8.25 | 6.375 × 10.125 | 7.5 × 11 | 1.625–2.25 | Manufacturer |
| PetSafe Extreme Weather Plastic — Medium / PPA00-10985 | 8.125 × 12.25 | 9.375 × 14 | 10.5 × 15 | 1.625–2.25 | Manufacturer |
| PetSafe Extreme Weather Plastic — Large / PPA00-10986 | 10.125 × 16.25 | 11.375 × 19 | 12.5 × 19.875 | 1.625–2.25 | Manufacturer |
| PetSafe Extreme Weather Aluminum — Medium / PPA00-16850 | 8.25 × 12.25 | 9.0625 × 13.75 | 10.875 × 15.625 | 1.5–2 | Manufacturer |
| PetSafe Extreme Weather Aluminum — Large / PPA00-16851 | 10.25 × 16.25 | 11.0625 × 17.875 | 12.75 × 19.625 | 1.5–2 | Manufacturer |
| PetSafe Extreme Weather Aluminum — X-Large / PPA00-16852 | 13.75 × 23.75 | 14.375 × 25.25 | 16.25 × 27.125 | 1.5–2 | Manufacturer |
Model names and region-specific part numbers can change. Compare your exact package, generation and supplied template before purchase or installation. The manufacturer catalogue, printed page 32, documents the six dimensional records; its older publication is not represented as a new product release.
Worked example: a pet match can fail as a replacement
A pet measures 7 inches wide and 11 inches from shoulder to belly. With a 1-inch total allowance, the planned passage is 8 × 12 inches. Extreme Weather Aluminum Medium has an 8.25 × 12.25-inch flap, leaving 1.25 inches beyond each body measurement and meeting that planning allowance.
Its required cut-out is 9.0625 × 13.75 inches. An existing 9.5 × 14-inch hole exceeds that requirement by 0.4375 inches in width and 0.25 inches in height. The outer frame is larger than the hole, but that fact alone does not establish a supported replacement. The tool therefore reports an oversized existing opening, even though the pet-passage check passes.
For a smaller 9 × 13.5-inch hole, the nominal required enlargement is 0.0625 inch in width and 0.25 inch in height. That is a dimension comparison, not an instruction to cut. Match the corner shape, placement and supplied template, and confirm the door structure permits the installation.
Read the labels as separate checks
Within your allowance means the flap clears both body dimensions by at least the selected total allowance. Below your allowance means the central measurements fit but the extra room falls short. Too small means the pet exceeds at least one flap dimension. None predicts willingness to push a flap or step over a sill.
Same nominal cut-out dimensions compares width and height only. Existing opening is smaller identifies a possible enlargement task. Existing opening exceeds required cut-out flags an unresolved replacement. Door-thickness and flat-panel checks have their own results, and an unmeasured value remains unknown.
For glass, walls or screens, the tool reports the installation surface as not evaluated. Do not apply solid-door dimensions to those projects. Use the exact maker’s installation instructions and any specified adapters; ask a suitable installer about the structure and material where necessary.
Before ordering or changing the opening
Make a full-size opening mock-up to assess your pet’s passage, then verify the actual flap and step-over arrangement. Keep door-handle hardware, panels, seals, closing covers and fastener locations in the installation review. A bigger size can improve passage yet need an outer frame that no longer fits the intended panel.
Consult PetSafe’s measurement guide and its Aluminum installation instructions for placement and project-specific details. Source checks are desk research; this site has not physically tested every pet door.
Common questions
Is the flap opening the same as the hole I cut?
No. The flap is the pet’s passage, the cut-out is the installation hole, and the outer frame covers and mounts around that hole. Compare all three for the exact model.
Can a larger frame fix an oversized existing hole?
Frame coverage alone does not establish an approved installation. Fastener position, corner shape, sealing, backing and the manufacturer’s replacement guidance still need to be checked.
Can this tool approve glass or wall installation?
No. The included records describe standard solid-door use. Glass, walls, screens and special panels need their own product instructions and any required adapters or professional installation.